FILTERS, REGULATORS & LUBRICATORS (FRL)
ADDITIONAL RESOURCES
ARO
Filter-regulator, or “piggybacks,” combine the functions of both a filter and regulator. Piggybacks are compact and most effective when space is a constraint. Piggybacks can be ordered with different filter elements and can be modified with different springs, depending on the filtration and air regulating requirements.
3000 Series Filter-Regulator "Piggyback"
3/4" & 1" sizes NPT and BSP thread options available
2000 Series Filter-Regulator "Piggyback"
3/8", 1/2", 3/4" sizes NPT and BSP thread options available
1500 Series Filter-Regulator "Piggyback"
1/4" & 3/8" sizes NPT and BSP thread options available
1000 Series Filter-Regulator "Piggyback"
1/8" & 1/4" sizes NPT and BSP thread options available
ARO-Flo compressed air filters are designed to remove airborne solid and liquid contaminants. Filters can be ordered with different elements, including coalescing models which are capable of removing oil aerosols and particles down to 0.3 micron. Standard filters are sold with 5-micron elements; 40-micron elements can be purchased and installed separately.
Super Duty Coalescing Filter
1-¼", 1-½", 2", 3" sizes NPT & BSP Thread Options Available
Super Duty Series Filter
1-¼", 1-½", 2", 3" sizes NPT & BSP Thread Options Available
ARO-Flo 3000
3/4" & 1" sizes NPT & BSP Thread Options Available
ARO-Flo 2000 Filters
3/8", 1/2", 3/4" sizes NPT & BSP Thread Options Available
ARO-Flo 1500 Filters
1/4" & 3/8" sizes NPT & BSP Thread Options Available
ARO-Flo 1000 Filters
1/8" & 1/4" sizes NPT & BSP Thread Options Available
Air line regulators provide controlled consistent air pressure as required for specific pneumatic equipment connected to the air system. All ARO-Flo regulators are offered with a standard adjustment range of 0-140 psig (0-9.6 bar). Alternative spring ranges are offered for easy conversion to suit different requirements. Non-relieving regulators are offered for applications where the venting of downstream overpressure is undesirable.
3000 Series Regulator
3/4" & 1" sizes 0-30, 0-60, 0-140 and 10-200 psi spring options
2000 Series Regulator
3/8", 1/2" & 1/4" sizes 0-30, 0-60, 0-140 and 10-200 psi spring options
1500 Series Regulator
1/4" & 3/8" sizes 0-30, 0-60, and 0-140 psi spring options
1000 Series Regulator
1/8" & 1/4" sizes 0-30, 0-60, and 0-140 psi spring options
Super Duty Series Regulator
1-1/4", 1-1/2", 2" sizes 0-125 and 0-180 spring options
Super Duty Series Lubricator
1-¼", 1-½ ", 2" sizes NPT and BSP thread options available
3000 Series Lubricator
3/4" & 1" sizes NPT and BSP thread options available
2000 Series Lubricator
3/8", 1/2" & 3/4" sizes NPT and BSP thread options available
1500 Series Lubricator
1/4" & 3/8" sizes NPT and BSP thread options available
1000 Series Lubricator
1/8" & 1/4" sizes NPT and BSP thread options available
Filters, regulators, lubricators, and piggybacks can be combined together to form combinations. They are typically strung together in the F+R+L arrangement (three-piece combo) and F/R+L (two-piece combo) arrangement, although other configurations are also used depending on application needs. ARO-Flo combination FRLs are easily assembled using modular spacer kits.
3000 Series 2-Piece Combination
3/4" & 1" sizes NPT and BSP thread options available
2000 Series Lubricator 2-Piece Combination
3/8", 1/2", 3/4" sizes NPT and BSP thread options available
1500 Series Lubricator 2-Piece Combination
1/4" & 3/8" sizes NPT and BSP thread options available
1000 Series Lubricator 2-Piece Combination
1/8" & 1/4" sizes NPT and BSP thread options available
3000 Series 3-Piece Combination
3/4" & 1" sizes NPT and BSP thread options available
2000 Series 3-Piece Combination
3/8", 1/2", 3/4" sizes NPT and BSP thread options available
1500 Series 3-Piece Combination
1/4" & 3/8" sizes NPT and BSP thread options available
1000 Series 3-Piece Combination
1/8" & 1/4" sizes NPT and BSP thread options available
CAMOZZI
Filter and Coalescing Filter Series N
Ports 1/8", 1/4" NPTF with threaded transparent bowl (Nylon - Grilamid)
The Series N filter is available with 1/8" and 1/4" NPTF ports. The bowl, which is transparent (Grilamid), makes monitoring of the condensate levels very easy and is equipped with manual and semiautomatic drain (plus 3 new drain options). The models are available with 3 different filtering elements: 5μm, 5μm and 0.01μm coalescing
MD Series Filter, Regulator & Lubricators - Maximum flexibility with compact dimensions
The new Series MD air preparation product line has been designed to meet the numerous demands of a market requiring light and compact modular products, which are characterized by high performance and flexible connection and orientation. The various functions are connected to each other by means of intermediate joining cartridges, which provide maximum porting flexibility to meet the needs of every application. Choose between six sizes of NPTF or BSPP threaded connections or six sizes of inch or metric push-in connections.The Series MD air treatment product line is characterized by a clean and modern design as well as high performance. The technopolymer construction enables effecient manufacturing and a lightweight, yet durable product. The innovative cartridge fitting design of the Series MD facilitates interchangeable port connection. The port cartridges may be female threaded or push-in fittings in various sizes from 1/8” to 3/8”. Each module also features additional 1/8” air outlets on the front and back sides.This inlet can be used by components with limited consumption requirements.
Coalescing Filters
Port 1/4", 3/8", 1/2" NPTF Modular with metal bowl guard and bayonet-type mounting
The Series MC coalescing filters are available with 1/4", 3/8", 1/2" NPTF port. The bowls of these filters are made of Nylon-Grilamid with an aluminum bowl guard and have a condensate drain valve in five (5) different options.
Electropneumatic / Pneumatic Isolation Valve (Shut-off)
These 3/2 way valves are designed to block the air at the inlet of the FRL group to pressurize or depressurize the equipment. The valves can either be electropneumatically or pneumatically operated and can be supplied with port 1/4", 3/8", 1/2" NPTF. In case of a solenoid valve use coil type U7… or G7… and the coil is ordered as a separate item.
Filters/Regulators
Port 1/4", 3/8", 1/2" NPTF Modular with metal bowl guard and bayonet-type mounting
The filter regulators Series MC are available with port 1/4", 3/8", 1/2" NPTF. They combine the features of the filters and regulators and have smaller overall dimensions than the two separate components.
Filters
Port 1/4", 3/8", 1/2" NPTF Modular with metal bowl guard and bayonet-type mounting
The Series MC filters are available with port 1/4", 3/8" or 1/2" NPTF. The bowls of these filters are made of Nylon - Grilamid with an aluminum bowl guard and have a condensate drain valve in five (5) different options. On request it is possible to order filters with filtering elements in different filtration ranges than those listed standard in the code key.
FRL Completed Assemblies (Single Part Number Code)
Ports 1/4", 3/8", 1/2" NPTF
The FRL Series MC Fully Assembled version are easier to order using one single part number code and to mount. The version with end-plate kit flanges is supplied without rear mounting bracket assembly, KIT B.
Functioning Condensate Drains Series MC and N
Lubricators Series MC
Port 1/4", 3/8", 1/2" NPTF Modular with metal bowl guard and bayonet-type mountingThe Series MC lubricators are available with port 1/4", 3/8", 1/2" NPTF. The bowls of these lubricators are made of metal and are equipped with a transparent viewer. The oil flow can be monitored via the small transparent cap and regulated by means of the special adjusting screw. In the 3/8" and 1/2" models, oil can be refilled while unit is under pressure by first removing the oil fill cap plug. Oil can be directly filled via cap plug. In addition, once cap plug is removed, the entire bowl may be removed for direct filling while system remains pressurized.
Manifold Pressure Regulators
Inlet port 1/4" NPTF, full Inlet pressure (non-cascading), 2 outlets per unit. ModularThe manifold pressure regulators are available with port 1/4" NPTF. Normally they are available with relieving diaphragm as standard and can be panel mounted.
Pressure Regulators
Port 1/4", 3/8", 1/2" NPTF ModularThe Series MC pressure regulators are available with port 1/4", 3/8", 1/2" NPTF. Relieving diaphragms are standard. Non-Relieving and Fast-Response Relieving diaphragms are optional, as called out in the code key. All versions can be panel mounted.
Activated Carbon Filters
Ports 3/4" - 1" NPTF Innovative modular clamping system Quick-Release, locking bayonet bowls
Series MX3 is the latest air treatment system offered by Camozzi. This modular design is characterized by a modern, compact design, and high performance. The integration between metal alloys and technopolymers has allowed the realization of a reliable product, both light and strong at the same time. The unique and patented modular clamping system simplifies the mounting of components. The Series MX appeals to a broad spectrum of markets and applications because of the savings realized in installation time, space requirements and total cost.
Coalescing Filters
Ports 3/4" - 1" NPTF Innovative modular clamping system Quick-Release, locking bayonet bowls
Series MX3 is the latest air treatment system offered by Camozzi. This modular design is characterized by a modern, compact design, and high performance. The integration between metal alloys and technopolymers has allowed the realization of a reliable product, both light and strong at the same time. The unique and patented modular clamping system simplifies the mounting of components. The Series MX appeals to a broad spectrum of markets and applications because of the savings realized in installation time, space requirements and total cost.
Filter-Regulators
Ports 3/4" - 1" NPTF Innovative modular clamping system Quick-Release, locking bayonet bowls
Filter-regulators Series MX integrate filter and pressure regulator in one unit. They are, therefore, compact and suitable for pre-filtering functions. Available in relieving or non-relieving, they are equipped with a valve diaphragm for a direct pressure regulation and with an integrated condensate drain, manual or automatic. Moreover, they can be equipped with a built-in pressure gauge.The Series MX has been realized to offer a multi-sector solution that guarantees saving in terms of installation time, space and costs.
Filters
Ports 3/4" - 1" NPTF Innovative modular clamping system Quick-Release, locking bayonet bowls
Series MX3 is the latest air treatment system offered by Camozzi. This modular design is characterized by a modern, compact design, and high performance. The integration between metal alloys and technopolymers has allowed the realization of a reliable product, both light and strong at the same time. The unique and patented modular clamping system simplifies the mounting of components. The Series MX appeals to a broad spectrum of markets and applications because of the savings realized in installation time, space requirements and total cost.
Lubricators
Ports 3/4" - 1" NPTF Innovative modular clamping system Quick-Release, locking bayonet bowls
Series MX3 is the latest air treatment system offered by Camozzi. This modular design is characterized by a modern, compact design, and high performance. The integration between metal alloys and technopolymers has allowed the realization of a reliable product, both light and strong at the same time. The unique and patented modular clamping system simplifies the mounting of components. The Series MX appeals to a broad spectrum of markets and applications because of the savings realized in installation time, space requirements and total cost.Pressure Regulators
Ports 3/4" - 1" NPTF Innovative modular clamping system Available with built-in pressure gauges or with front & rear ports for gaugesReliable and repeatable set-points of the secondary reduced pressure ensures performance optimization and energy saving. Available in 2 standard spring options for regulated pressure ranges. All regulators are equipped with an integrated locking system and built-in pressure gauges for a more compact product. The regulators Series MX are suitalbe also for panel mountings.
CKD
Combination
Compact modular design in which major boundary dimensions of devices such as filters, regulators, lubricators, etc., are unified.
F.R.L. combination copper and PTFE free
Copper ion prevention treatment specifications. Combination of filter/regulator/lubricator.
Compact F.R.L. Kit / Set
Filter / regulator / lubricator set K Series for nipple connection are available in a wide range of models.
Combination
Compact modular design in which major boundary dimensions of devices such as filters, regulators, lubricators, etc., are unified.
Combination
Compact modular design in which major boundary dimensions of devices such as filters, regulators, lubricators, etc., are unified.
Filter / Regulator
New Series using integrated filter and regulator, 5μm elements for dust removal, and 0.3μm elements for tar removal.
Filter / regulator flame-resistant
A flame-resistant integrated filter and regulator that is resistant to spatter.
Filter / Regulator / Copper and PTFE free
Filter and regulator are integrated and copper ion prevention treatment is provided.
Filter / regulator for outdoor use
For the first time in the industry, long-term outdoor use is guaranteed, even in harsh environments.
Compact Filter / Regulator
Ideal for semiconductor manufacturing lines and compact equipment fields. Compact, space saving structure and reverse flow function integrated.
Compact Filter / Regulator Unit
Compact F.R. unit with integrated filter and regulator. 5 μm element is used for dust removal.
Antimicrobial / Antibacterial filter
Ideal for circuits that blow directly on food. Sterile clean air is provided. In addition, an odor removal filter has been added to the lineup to supply odorless air (gases). It contributing further to safe and clean air (gases).
Oil mist filter
Effectively removes oil and oil mist from pneumatic lines.
Air filter
New Series using 5μm elements for dust removal, and 0.3μm elements for tar removal.
Air filter flame-resistant
Modular design FRL series, flame-resistant and resistant to spatter.
Air filter medium pressure
F3000 to F8000 Series medium pressure specifications. The maximum working pressure is 1.6 MPa and proof pressure is 2.4 MPa
Air filter Outdoor
For the first time in the industry, long-term outdoor use is guaranteed, even in harsh environments.
Oil mist filter medium pressure
M3000 to M8000 Series medium pressure specifications. The maximum working pressure is 1.6 MPa and proof pressure is 2.4 MPa.
High performance oil mist filter
Secondary oil content 0.001 mg/㎥ Appropriate for optical devices, such as optical positioning devices and laser processing systems.
Oil mist filter for outdoor use
For the first time in the industry, long-term outdoor use is guaranteed, even in harsh environments.
Compact air filter
Compact air filter for dust removal. [Port size] Rc1/8 to 1/4
Large bore size filter
Nipple connection large bore size filter. Diverse lineup of both series and sizes.
Clean exhaust filter
Provides direct exhaust within clean rooms. Revolutionary filter / clean exhaust filter that can clean exhaust air used in pneumatic circuits with high accuracy by adopting a hollow fiber membrane structure.
Inline clean filter
Inline clean filter with hollow fiber membrane for filter element provides high performance in all aspects including filtration performance, flow rate, pressure loss, service life and installation space.
Inline filter
Compact, lightweight and space saving inline filter.
Medium main line filter
Lower pressure loss, longer life and a more compact size have been realized by adopting new materials and new structure. Energy saving element used/simple element replacement / equipped with drain discharger. (Applicable compressor) 22 kW to 95 kW
Medium main line stainless steel filter (oil free)
Lower pressure loss, longer life and a more compact size have been realized by adopting new materials and new structure. Energy saving element used/simple element replacement / equipped with drain discharger. (Applicable compressor) 22 kW to 95 kW
Medium main line filter
High performance main line filter with stainless steel housing for clean environments. Simple element replacement / replacement interval can be managed by time. (Applicable compressor) 22 kW to 95 kW
Large main line filter
Simple system configuration is realized thanks to a unified design of filter vessels. Incorporated energy saving element / differential pressure gauge is equipped as standard. (Applicable compressor) 95 kW to 1450 kW
Large main line filter (oil free) / pre-filter
A stainless steel vessel is used to eliminate concerns about rust, and to supply perfectly clean high quality air. Incorporated energy saving element / remote control possible. (Applicable compressor) 95 kW to 1450 kW
Regulator
Compact, pressure gauge embedded. The pressure can be adjusted without tools.
Precision regulator RP1000 & RP2000
A compact type with a large relief flow rate that demonstrates highly precise pressure control and stable flow characteristics with low pressure drop.
Precision regulator PRE
An eco-friendly, new type of precision regulator. Significant reduction in air consumption is achieved with the special structure. As it has excellent control performance, high precision and a compact size, it can be used for various applications including precise tension control.
Regulator for water WR
Easy-to-use compact regulator for water. Specially designed knob shape for easy pressure adjustment, with mesh filter supplied as standard.
Regulator flame-resistant
A flame-resistant regulator / reverse regulator that allows pressure adjustment without a tool and is resistant to spatter.
Regulator / medium pressure
R3000/R4000-W Series medium pressure specifications. The maximum working pressure is 1.6 MPa and proof pressure is 2.4 MPa.
Regulator / Oil-prohibited
Ideal for applications susceptible to grease, including liquid crystal, semiconductors, foodstuffs, medical use, and electrical potential parts. All parts in the fluid passage area are degreased and washed, and use no grease.
Regulator / copper and PTFE free specification
The pressure can be adjusted without tools. Copper ion prevention treated.
Regulator for outdoor use
First in the industry. Long-term outdoor use is guaranteed, even in harsh environments. [Port size] Rc1/4 to 1
Compact filter / Regulator for outdoor
For the first time in the industry, long-term outdoor use is guaranteed, even in harsh environments.
Compact regulator RB500 & MNRB500
Compact, space saving structure and reverse flow function integrated compact regulator.
Compact piston regulator RA800
Compact, lightweight piston regulator with improved operability.
Vacuum regulator VRA2000
Ideal for circuits that require precise pressure adjustment such as fine workpiece suction or inspection systems. Compact, large flow rate and high precision vacuum regulator.
Dial air regulator 2302・2303・2304
Dial is provided to enable easy pressure adjustment and remote control. (Remote control type only)
Large bore reverse regulator 2415
Smooth discharge of secondary side with check valve. No bypass circuit required and easy piping.
Large bore regulator 2215・2216
Large bore regulator.
Compact direct acting precision regulator
Grease-free specification, compact and space saving compact direct acting precision regulator. The push-in fitting improves the workability. Ideal for semiconductor manufacturing post processes, IT applications, and compact assembly, etc., requiring space saving, precision, and grease-free products. Block manifold MNRJB500 Series can act as a mixed manifold with RJB500 / RB500 Series.
Lubricator L※000
Supplies fine oil mist. A double plastic structure is adopted, so oil dripping can be confirmed from any angle.
Compact lubricator A3019
A compact lubricator. Supplies fine oil mist.
Large bore lubricator 3003E・3004E・3005E
A large lubricator. Supplying fine oil mist (oil fog).
Lubricator for outdoor use LW※000
Outdoor lubricator series that guarantees long-term outdoor use even in harsh environments.
CLIPPARD
FILTERS, REGULATORS & LUBRICATORS
Maximatic FRLs condition and prepare compressed air for use in fluid power systems. Pneumatic applications with properly conditioned air will operate longer, cost less and improve system efficiency. Clippard offers many different sizes from #10-32 to 1” NPT of filters, regulators, lubricators, and combination units. Their modular design and interconnecting brackets provide flexibility and facilitate simple field installation and/or modification
FILTER-REGULATOR-LUBRICATOR COMBINATION UNITS
Combination FRLs provide air filtration, regulation and lubrication in one unit for easy mounting and installation. Includes L brackets and gauge.
STACKING FILTER-REGULATOR-LUBRICATORS
Stacking FRLs provide air filtration, regulation and lubrication in one unit for easy mounting and installation. Includes L bracket and gauge
FILTERS
Maximatic filters remove moisture and contaminants, and provide air filtration through a 25 micron filter. Replacement 25 micron and 5 micron filters are available.
REGULATORS & LUBRICATORS
Maximatic regulators provide precise air regulation from 7 to 125 psig. The adjustment knob must be pulled out to adjust the pressure, preventing accidental adjustment. Maximum inlet pressure is 150 psig. Includes bracket and gauge.
COILHOSE
Heavy Duty 88 Series
The Heavy Duty Series will Provide Years of Service
29 Series
The 29 Series is a Lightweight, Modular Design
27 Series
The 27 Series Provides Exceptional Modular Design and Installation Flexibility
In-Line Series
The In-Line Series of Filters, Regulators, and Lubricators Provides a Convenient On-Tool Installation
Miniature Series
A Small, Compact Series Designed for Limited Space Applications
26 Series
The 26 Series is a Careful Balance of Size and Flow
Desiccant Dryers
Desiccant Dryers use Chemical Reactions to Remove Moisture from Compressed Air Systems
Drain Units
Automatically Removed Moisture and Accumulated Condensation in Your Compressed Air System with Drain Units.
Economy Regulators
Lightweight and Cost-Effective, this Compact Regulator is designed for a Long Service Life
General Purpose Series
A Broad Offering of Units ranging from 1/4” to 2”
MARSH BELLOFRAM
Marsh Bellofram Filter-Regulator-Lubricators (FRLs) are designed with economy and convenience in mind. Filter Regulators have the same features as the regulators with the addition of polycarbonate bowls, 5 or 50 micron filters, and with manual, semi-automatic or automatic drains. Lubricators feature polycarbonate bowls, with field- settable dials providing variable lubrication between 0 and 90 drips per minute.
Filter Regulator Lubricator Assemblies (FRLs)
Marsh Bellofram FRL’s are pre-packaged, modular assemblies of popular configurations of air filters, regulators and lubricators offered as a single unit. Designed with economy and convenience in mind, Marsh Bellofram FRL’s are available in miniature and standard sizes. Regulators incorporate a balanced poppet and relieving type diaphragm, with a metal body, polycarbonate bonnet, a non-rising adjustment knob and panel, pipe or bracket mounting capabilities.
Filter regulators offer the features as the pressure regulators with the addition of 5, 25 or 50 microfilters, polycarbonate bowls, and the choice or manual, semi-automatic and automatic drains. Lubricators feature polycarbonate bowls and a field settable adjustment of the lubrication level. Units are available in 0-10, 3-30, 3-60 and 7-140 PSIG output pressure ranges with a maximum supply of 140 PSIG(280 PSIG w/metal bowl option). FRL’s are offered with a choice of 1/8, 1/4, 3/8, 1/2,3/4 and 1 NPT pipe sizes. The modular design facilitates easy maintenance and swap-out of the filter, regulator or lubricator.
Features:
Applications:
MASTER PNEUMATIC
General Purpose Filters
General purpose compressed air filters remove water and particulate material from the air stream to protect downstream equipment from contamination. As air enters the filter, internal baffles create a swirling motion to the air so that entrained dirt and liquids are thrown against the sides of the filter bowl and then fall to the sump area at the bottom of the bowl. Additional baffling keeps the air in the sump area relatively quiet; this ensures that the removed material is not returned to the air flow going to the filter element. The filter element will then collect smaller particles. The most frequently used element in Master Pneumatic general purpose filters is rated at 5 µm, so that nearly all particles larger than 5 µm (half the diameter of a human hair) will be collected in the filter element.
Coalescing Filters
A 0.3-µm-rated coalescing filter element is standard in all coalescing units. They remove 99.99% of oil and solid contaminants larger than 0.3 µm. An optional 0.01-µm-rated element provides extremely fine filtration, but at some reduction in air flow. However, in GUARDSMAN, GUARDSMAN II, SERIES 380, and VANGUARD filters there are available extended bowls with higher capacity coalescing elements for significantly increased air flows. Coalescing filters have epoxy-resin-coated, borosilicate, glass fiber elements. Liquids and solids are removed from the air stream by several different actions, namely:
IMPACTION: Particles larger than 1 µm collide with and adhere to the fibers of the element.
INTERCEPTION: Particles 0.3 µm to 2 µm in size are molecularly attracted to the fibers of the element, and this causes them to adhere.
DIFFUSION: Particles 0.001 µm to 0.3 µm in size move by random Brownian motion, thereby contacting and adhering to the fibers of the element.
DRAINING: Tiny droplets of oil coalesce (merge) until they form drops large enough to fall off the filter element and into the bowl sump. The automatic drain then expels them.
The filter element will continue to coalesce liquids until solid contaminants accumulated in the filter element cause the pressure drop across the element to become excessive. At this point the filter element must be changed. A built-in differential pressure gauge will indicate when the point is reached that requires the element to be changed.
Adsorbing Filters - Oil Vapor Removal
OIL REMOVAL ADSORBING FILTERS
The adsorbing filters are designed to remove vapors from the air line that cannot be removed by a coalescing filter. They produce air that is virtually free of oil and hydrocarbons as required by industries such as food processing, electronics, and instrumentation. The filter cartridges contain activated carbon to adsorb hydrocarbon vapors and odors from alcohols, esters, and ketones. An optional extended bowl includes a higher capacity adsorbing cartridge which allows as much as 50 percent greater air flow. Series BFC70-E9 adsorbing filters have aluminum bowls and are offered with 1/4, 3/8, or 1/2 ports. Series FC380-E9 units have either polycarbonate plastic or aluminum bowls and are offered with 3/8, 1/2, or 3/4 ports. An adsorbing filter should always be preceded by a particulate filter and a coalescing filter. Such an assembly is one of Master Pneumatic’s Clean Air Packages which will provide air with no more oil than 10 mg/m3 or 0.008 ppm.Dryer Filters
MP-FILENCO DRYER / FILTERS
Many compressed air systems require point-of-use cleaning and drying of the air to supplement a central system. Dryer/filters do this extremely well because of their triple-action cleaning process and their ability to substantially reduce pressure dew points. Available desiccants for these units include clay, clay with activated carbon, and molecular sieve for as much as 80° dew point suppression. Automatic drains are strongly recommended, although there are a variety options offered — from manual drains to the Warrior electronic drain.Clean Air Package
MP-FILENCO DRYER / FILTERS
In critical applications when vapor impurities a are a potential problem, the installation of a Clean Air Package provides the solution. Ultra clean air is provided by using the particulate filters as the fi rst line of defense against gross contaminants found in all air lines. Elements remove solid particles larger than 5 micron, while automatic drains eliminate liquid water and oil emulsions that collect in the sump area. The particulate filter serves as a pre-fiter to extend the life of the more costly coalescing element used for the next stage of filtration. The coalescing filter element will further clean the air of residual oil mists, aerosols, and minute particles, larger than 0.3 micron. A standard differential pressure gauge warns when the pressure drop exceeds 8 to 10 psi, indicating that the coalescing element should be changed. Finally, the adsorber fi lter will provide air, virtually free of oil and most hydrocarbons. It effectively eliminates odors from freons, alcohols, esthers, ketones, and up to 99% of most hydrocarbons. Clean Air Packages are available with port sizes ranging from 1/4 to 3/4.Breathing Air Assemblies
MP-FILENCO DRYER / FILTERS
Master Pneumatic’s breathing air assemblies are designed with 2 and 4 drops to provide breathing air for up to 4 workers. A Breathing Air assembly can allow end users to achieve "grade D" breathing air as defined by the Compressed Gas Association's commodity specification: G-7.1 (www.cganet.com). The general purpose filter in an assembly removes gross contaminants while the coalescing filter removes oil mists, aerosols and minute particles. The adsorbing filter effectively eliminates odors from freons, alchohols, esters, keytones and up to 99 percent of most hydrocarbons. The CO monitor is designed to detect and alert user to the presence of CO if the level is 10 ppm or greater as stated in OSHA title 29 section 1910.134(D)(1)&(2) ANSI/CGA standard G-7.1General Purpose Regulators
M a s t e r P n e u m a t i c regulators are made in a wide range of sizes to suit nearly all industrial requirements for pneumatic pressure regulation. Good pressure regulation is essential to the efficient use of pneumatic equipment. A compressor may supply air at 150 psig, but most of the equipment will operate best at lower pressures. A cylinder, for example, may develop sufficient force for its purpose with 50- psig air. Remember that compressed air is costly, so using higher air pressure than necessary is wasteful, and may also shorten the life of the cylinder. A general purpose pressure regulator is the answer for greater economy and efficiency. Regulators are of two basic designs. Piston design provides highest airflow; diaphragm design provides high sensitivity and quick response. All regulators are self-relieving, but a non-relieving option is available. A pressure gauge is standard, and gauge ports are at the front and the rear of each unit. In addition there are precision regulators in all port sizes for applications demanding extra precision in the regulation of air pressure, plus regulators for remote, external piloting.
MODULAR or INLINE MOUNTING
SENTRY, GUARDSMAN, SERIES 380, and Full Size VANGUARD regulators are of modular design. Regulators are connected to filters or lubricators by special modular connectors which seal the faces between units. They may also be inline mounted with pipe nipples. MINIATURE and High-Capacity VANGUARD regulators are inline mounted only.
SENTRY REGULATORS
Port sizes 1/8 and 1/4 or fittings for tubing up to 10 mm. Modular units have durable plastic, corrosion resistant bodies. A non-relieving version can be used with water, oil, and many other liquids.
Precision and Internal Regulators
Externally Piloted Regulators
Water Pressure Regulators
Relief Valves
Servo Valves
CO2 / Nitrogen Regulators
Manifold Regulators
Air line lubricators are designed to introduce atomized oil into the air line so that downstream mechanisms can be adequately lubricated. Lubricators should be adjusted so that the minimum amount of oil to lubricate the equipment is used. Excess oil will simply be blown into the atmosphere and pollute the environment. There are two basic designs used in Master Pneumatic lubricators: sight-feed design and wick-feed design. Illustrations of these two types of assembly are shown on the facing page.
SIGHT-FEED LUBRICATORS
Air flows through a flexible-vane automatic flow sensor that creates a small pressure differential between the air passage and the oil reservoir. This differential causes oil to move up a riser tube, through an adjustable metering valve, and then to drip into a transparent dome and the air stream. This oil is “atomized” by the air stream, and carried down the air line to the points of lubrication.
Sight-feed lubricators are easy to adjust, and an indicator on the sight dome measures the amount of oil dispensed. The adjusting knob can be removed to make the lubricator “tamper-resistant.” All working parts are in an easily replaceable cartridge. Note: Not recommended for valve and cylinder circuits (see INJECTION LUBRICATORS section).
WICK-FEED LUBRICATORS
In a wick-feed lubricator one end of a porous bronze wick is saturated with oil in the reservoir. Capillary action causes the oil to travel up the wick. Oil is stripped off the upper portion of the wick by the air fl ow, and maintains a constant oil-to-air ratio. This ratio can be varied by manual adjustment. Units will not shut off, even with dirt and moisture in the reservoir. However, air must be shut off when filling the reservoirs of these models.
MODULAR or INLINE MOUNTING
SENTRY, GUARDSMAN, SERIES 380, and Full-Size VANGUARD lubricators are of modular design. They are connected to other units by special modular connectors which seal the faces between units. They may also be inline mounted with pipe nipples. MINIATURE and High-Flow VANGUARD lubricators are inline mounted only.
Single Point Lubricators - SPL
SERV-OIL is the most advanced system for the precision lubrication of pneumatic equipment. It has been used for over thirty years to provide lubrication to all kinds of pneumatic equipment and various fixtures, bearings, slides and ways. It overcomes the control problems that can be encountered with conventional mist lubricators. It also ensures proper lubrication of pneumatic components in complex circuits, and accurately delivers lubricant to points at a long distance from lubricator.
Positive displacement oil injectors called Servo-Meters are the heart of Serv-Oil equipment. They put pre-determined, precise amounts of oil right at the points where lubrication is needed. by compariison, mist lubricators lack the precision and control of a Serv-Oil system. Extensive tests have shown that when a conventional mist lubricator is installed upstream of a control valve, much of the oil dispensed by the lubricator is exhausted to atmosphere through the exhaust port of the control valve. This is inefficient and also contributes significantly to pollution of plant air.
With Serv-Oil equipment the amount of oil used is greatly reduced and lubrication is more effective because of the accuracy with which the oil is delivered.
Briefly: Serv-Oil lubricates the component, not the area!
Maximum performance. Extended life. Reduced maintenance. Less downtime. Improved torque control. These are all results of precise, consistant lubrication.
Features:
The Serv-Oil Single Point Injection Lubricator for Air Tools is specifically designed to inject a predetermined amount of oil at the inlet of an air tool every time it cycles, every 5th cycle or every 10th cycle. The Serv-Oil Single Point Downstream Injection Lubricator is designed to be installed downstream of control valve using a small nylon tube to deliver oil to desired lubrication point for cylinders, air motors, or other pnuematic equipment. Specifications: Both Single Point Injection Lubricators are offered in two port sizes, 1/2 inch and 3/4 inch. Dispensing volumes of .016 cc, .033 cc and .066 cc and adjustable from every cycle to every 10th cycle. With the addition of another counter this can be increased to every 100th cycle. Options of either a 10 oz. reservoir or no reservoir are available.
Hose Assemblies with and without FR-SPL
Multiple Point Lubricators - MPL
SERV-OIL is the most advanced system for the precision lubrication of pneumatic equipment. It has been used for over thirty years to provide lubrication to all kinds of pneumatic equipment and various fixtures, bearings, slides and ways. It overcomes the control problems that can be encountered with conventional mist lubricators. It also ensures proper lubrication of pneumatic components in complex circuits, and accurately delivers lubricant to points at a long distance from lubricator.
Positive displacement oil injectors called Servo-Meters are the heart of Serv-Oil equipment. They put pre-determined, precise amounts of oil right at the points where lubrication is needed. by compariison, mist lubricators lack the precision and control of a Serv-Oil system. Extensive tests have shown that when a conventional mist lubricator is installed upstream of a control valve, much of the oil dispensed by the lubricator is exhausted to atmosphere through the exhaust port of the control valve. This is inefficient and also contributes significantly to pollution of plant air. With Serv-Oil equipment the amount of oil used is greatly reduced and lubrication is more effective because of the accuracy with which the oil is delivered.
Liquid Delivery Systems
The integration of a general purpose fi lter and a pressure regulator into a single module provides the compactness needed where space is limited. These integral filter/regulators are offered by Master Pneumatic in port sizes from 1/8 up to 3/4 along with models equipped with quick-connect fittings for tubing from 1/4 up to 10 mm. The regulator is the top portion of the assembly, and the filter is the bottom portion. All sizes have essentially the same operating characteristics as their corresponding individual filters and regulators. All filter/regulators include an internal automatic filter drain and a pressure gauge as standard equipment. Regulators are self relieving, and have gauge ports front and rear. Nonrelieving models are also available. Available options are the same as those for the corresponding individual filters and regulators. They include regulating springs for various pressure ranges, metal filter bowls, and sintered bronze filter elements in several µm ratings.
MODULAR or INLINE MOUNTING
SENTRY, GUARDSMAN, SERIES 380, and Full-Size VANGUARD integral filter/regulators are of modular design. Units can be connected to lubricators by special modular connectors which seal the faces between units. They may also be inline mounted with pipe nipples. MINIATURE filter/regulators are designed for inline mounting only. All units are available with either NPTF or BSPP port threads. SAE threads are also available on GUARDSMAN, SERIES 380, and Full-Size VANGUARD models.
The integration of a general purpose fi lter and a pressure regulator into a single module provides the compactness needed where space is limited. These integral filter/regulators are offered by Master Pneumatic in port sizes from 1/8 up to 3/4 along with models equipped with quick-connect fittings for tubing from 1/4 up to 10 mm. The regulator is the top portion of the assembly, and the filter is the bottom portion. All sizes have essentially the same operating characteristics as their corresponding individual filters and regulators. All filter/regulators include an internal automatic filter drain and a pressure gauge as standard equipment. Regulators are self relieving, and have gauge ports front and rear. Nonrelieving models are also available. Available options are the same as those for the corresponding individual filters and regulators. They include regulating springs for various pressure ranges, metal filter bowls, and sintered bronze filter elements in several µm ratings.
Integral CFRL Combinations
The integration of a general purpose filter and a pressure regulator into a single module provides the compactness needed where space is limited. These integral filter/regulators are offered by Master Pneumatic in port sizes from 1/8" up to 3/4" along with SENTRY models equipped with quick-connect fittings for tubing from 1/4" up to 10 mm.
When an integral filter/regulator is paired with a lubricator, joined either by a modular connector or a pipe nipple, the assembly makes a complete FRL with nothing lost in performance, but with the advantage of compactness to fit in tight spaces. All filter/regulators include an internal automatic filter drain and a pressure gauge as standard equipment, and regulators are either self-relieving or non-relieving. SENTRY, GUARDSMAN, and SERIES 380 assemblies include a lockout valve for added safety.
Available options are the same as those for the corresponding individual filters, regulators, and lubricators. They include regulating springs for various pressure ranges, metal filter bowls, and sintered bronze filter elements in several µm ratings, as well as quick-fill caps for the lubricators. All assemblies, except Miniatures, now include a lockout valve for increased safety.
FRL Combinations
FRL assemblies offer an enormous variety of combinations to fit the needs of almost every filtration, pressure regulation, and lubrication requirement. The FRLs shown in this catalog cover only a portion of these needs in port sizes from 1/8" to 1-1/2". Featured are the configurations most widely used, but FRLs in many other configurations are readily assembled.
All standard SENTRY,GUARDSMAN, Full-Size VANGUARD, and SERIES 380 assemblies now include a lockout valve for added safety.
General purpose filter-regulator-lubricator assemblies are the most widely used, but other combinations meet a variety of needs. For example, where air line lubrication is not needed, a filter-regulator combination may be sufficient. This can consist of an individual filter and regulator or a compact integral filter/regulator.
PARKER / WATTS
Parker offers a range of air-line, pressure high flow and single phase regulators for instrumentation, filtration, refrigeration and pneumatic applications. Instrumentation regulators are used in the process, power, oil, gas and semiconductor industries to control the flow of liquids and gases with speed and precision. Air regulators provide quick response and accurate pressure regulation for the most demanding industrial air preparation applications, available as miniature, economy, compact, standard, hi-flow and pilot-operated regulators to meet a variety of service needs. The refrigeration line of pressure regulators includes valves that control inlet, outlet or differential pressure. Each regulator is available with an assortment of variations which enable one regulator to perform multiple functions. All regulators are built to the highest quality standards, recognized around the world for their performance, durability and reliability.
Economy Filter Regulator - 05E Series Prepair II
05E is a compact particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. 05E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Compact Filter Regulator - 06E Series Prepair II
06E is a compact particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. 06E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Standard Filter Regulator - 07E Series Prepair II
07E is a standard particulate filter/reg that provides accurate pressure regulation and high moisture removal efficiency in a compact package. 07E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Standard Coalescing Filter Regulator - 12E Series Prepair II
12E is a coalescing filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. 12E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Miniature Filter Regulator - 14E Series
14E is a miniature particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. 14E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Precision Filter Regulator - 27E Series Prepair II
Precision Filter Regulator - 27E Series Prepair II 27E is a compact semi precision integral particulate filter/regulator that provides extremely accurate pressure regulation and high moisture removal efficiency in a compact one piece package.
Miniature Filter Regulator - B34 Series
B34E is a mini particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. B34E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Global Modular Mini Filter Regulator - P31E Series
P31E is a mini particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. P31E is a one piece filter/regulator which minimizes space by incorporating two units into one.
Global Modular Semi-Precision Filter Regulator - P32E Series
P32E is a semi-precision particulate filter/regulator that provides extremely accurate pressure regulation and high moisture removal efficiency in a compact package. This combined filter/regulator minimizes space by incorporating two units into one.
Global Modular Compact Filter Regulator - P32E Series
P32E is a compact particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. P32E is a one piece combined filter/regulator which minimizes space by joining two units into one.
Global Modular Standard Filter Regulator - P33E Series
P33E is a compact particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. P33E is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Precision Filter Regulator - P3EA632 Series
The P3EA632 precision particulate filter/regulators provide extremely accurate pressure regulation and high moisture removal efficiency in a compact package. These one piece combined filter/regulators minimize space by incorporating two units into one.
Hi-Flow Filter Regulator - P3NE Series
P3NE is a high flow filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. P3NE is a one piece combined filter/regulator which minimizes space by incorporating two units into one.
Global Hi-Flow Filter Regulator - P3YE Series
P3YE is a particulate filter/regulator that provides accurate pressure regulation & high moisture removal efficiency in a compact package. P3YE is a one piece combined filter/regulator which minimizes space and piping by incorporating two units into one
Stainless Steel Standard Filter Regulator - PB11, PB12 Series
PB11/12 is a stainless steel particulate filter/regulator that provides accurate pressure regulation and high moisture removal efficiency in a compact package. This one piece combined filter/regulator minimizes space by incorporating two units into one.
Stainless Steel Miniature Filter Regulator - PB548, PB558 Series
PB548/58 is a stainless steel particulate filter/regulator that provides accurate pressure regulation & high moisture removal efficiency in a compact package. This one piece combined filter/regulator minimizes space by incorporating two units into one.
Miniature Filter Regulator - 14E Series
14E is a 40mm mini combined filter/regulator, 1/8" & 1/4" ported BSPP/NPT, 5µ element, poly bowl fitted with twist/automatic drain. Max P1 pressure of 10 bar with P2 ranges 0 to 2, 4 & 8 bar. Temp from 0°C to 52°C.
Global Modular Mini Filter Regulator - P31E Series
P31E is a 40mm mini combined filter/regulator, 1/4" ported BSPP/NPT, 5µ element, poly/metal bowl fitted with manual/pulse drain. Max P1 pressure of 17 bar with P2 ranges 0 to 2, 4, 8 & 16 bar. Temp from -10°C to 65.5°C.
Global Modular Semi-Precision Filter Regulator - P32E Series
P32E is a 60mm compact semi-precision filter/regulator, 1/4",3/8" & 1/2" ported BSPP/NPT, 5µ element, poly/metal bowl fitted with manual/auto drain. Max P1 pressure of 17 bar with P2 ranges 0 to 2, 4, 8 & 17 bar. Temp from -25°C to 65.5°C.
Global Modular Compact Filter Regulator - P32E Series
P32E is a 60mm compact combined filter/regulator, 1/4",3/8" & 1/2" ported BSPP/NPT, 5µ element, poly/metal bowl fitted with manual/auto drain. Max P1 pressure of 17 bar with P2 ranges 0 to 2, 4, 8 & 17 bar. Temp from -25°C to 65.5°C.
Global Modular Standard Filter Regulator - P33E Series
P33E is a 73mm standard filter/regulator, 1/2" & 3/4" ported BSPP/NPT, 5µ element, poly/metal bowl fitted with manual/auto drain. Max P1 pressure of 17 bar with P2 ranges 0 to 2, 4, 8 & 17 bar. Temp from -25°C to 65.5°C.
P3L Lite FRL System Air Pressure Filter Regulators - P3LE Series
P3LE is a 40mm mini lightweight filter/regulator, 1/4" ported BSPP/NPT, 5/40µ element, poly bowl fitted with manual/semi-auto drain. Max P1 pressure of 10 bar with P2 ranges 0 to 2, 4 & 8 bar. Temp from 0°C to 50°C.
P3X Moduflex Lite FRL System Air Pressure Filter Regulators - P3XE Series
P3XE is a 62mm lightweight filter/regulator, 1/2" & 3/4" ported BSPP (NPT 1/2" only), 5/40µ element, high tech polymer bowl fitted with combi manual/semi-auto or auto drain. Max P1 pressure 16 bar with P2 ranges 0 to 4, 8 & 16 bar. Temp -40°C to 60°C
P3Y Air Prep System Air Pressure Filter Regulators - P3YE Series
P3YE is a 90mm filter/regulator, 3/4" & 1" ported BSPP/NPT, 5/40µ element, poly insert & metal bowl fitted with combi manual/semi-auto or auto drain. Max P1 pressure of 17.5 bar with P2 ranges 0 to 12 & 16 bar. Temp from -40°C to 60°C.
Stainless Steel Standard Filter Regulator - PB11, PB12 Series
PB11/PB12 is a 60mm S/Steel (316) filter/regulator, 1/2" ported BSPP/NPT, 5/40µ element, metal bowl fitted with manual/auto drain. Max P1 pressure of 20.7 bar with P2 ranges 0 to 4, 8 & 17 bar. Temp from -18°C to 82°C.
Stainless Steel Miniature Filter Regulator - PB548, PB558 Series
PB548/PB558 is a 40mm S/Steel (316) filter/regulator, 1/4" ported BSPP/NPT, 5/20µ element, metal bowl fitted with manual/auto drain. Max P1 pressure of 20.7 bar with P2 ranges 0 to 1.7, 4 & 8 bar. Temp from -18°C to 82°C.
AF200 / 320 / 420 - Compact Particulate Air Filter
Parker Automation Korea Division's AF Series is comapct and modular style air filter, which combines the element and bowl in one piece, making element replacement easy.
AFR (AFR200 / AFR320 / AFR420) is Combination Filter/Regulator, minimizing space and piping by intergrating two units into one.
AFR series is a precision particulate filter/regulator that provides extremely accurate pressure regulation and high moisture removal efficiency in a compact package. This combined filter/regulator minimizes space by incorporating two units into one.
Air Lubricators provide lubrication for most general air preparation applications in a pneumatic system. Parker Air Lubricators provide optimum and uniform lubrication with fine micro-mist particles of 2 micron or smaller to pneumatic components, including those with complex piping arrangements.
Micro-Mist Lubricators - Prep-Air II 15L Series (Economy)
The 15L is an economy micro-mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of lubrication for air tools and other pneumatic devices. Lubrication rate can also be adjusted manually.
Micro-Mist Lubricators - Prep-Air II 16L Series (compact)
The 16L is a compact micro-mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of lubrication for air tools and other pneumatic devices. Lubrication rate can also be adjusted manually.
Micro-Mist Lubricators - Prep-Air II 17L Series (standard)
The 17L is a standard micro-mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of lubrication for air tools and other pneumatic devices. Lubrication rate can also be adjusted manually.
Standard Mist Lubricators - 09L Series (Large High-Flow)
The 09L is a large industrial mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Standard Mist Lubricators - L606 Series (Heavy Duty High-Flow)
The L606 industrial mist lubricator injects an oil mist into the air stream to provide the right amount of internal lubrication for pneumatic devices and can be precisely adjusted to a low oil flow rate.
Standard Mist Lubricators - P3NL Series (High-Flow)
Parker's P3NL is a mist lubricator that injects an oil aerosol into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Global Standard Mist Lubricators - P3YL Series (High-Flow)
Parker's P3YL is a global mist lubricator that injects an oil aerosol into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Stainless Steel Standard Mist Lubricators - PL10 Series (Standard)
The PL10 is a stainless steel mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Standard Mist Lubricators - 02L Series (In-line Miniature)
Parker's 02L is an in-line lubricator that will assure proper lubrication for small pneumatic hand tools. These in-line lubricators put the oil source right at the tool.
Standard Mist Lubricators - 04L Series (Miniature)
The 04L is a mini mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Standard Mist Lubricators - 06L Series (Compact)
The 06L is a compact mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Standard Mist Lubricators - 07L Series (Standard)
The 07L is a standard mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
P3XL Series Nano-mist Lubricator
P3XL is a 62mm lightweight nano-mist lubricator, 1/2" & 3/4" ported BSPP (NPT 1/2" only), high tech polymer bowl. Max P1 pressure of 16 bar. Temp from -10°C to 60°C.
Miniature Mist Lubricator - 04L Series
04L is a 40mm mini mist lubricator that injects an oil aerosol into the flowing air stream, 1/8" & 1/4" ported BSPP/NPT, poly bowl. Max P1 pressure of 10 bar. Temp from 0°C to 52°C.
P3L Lite Mist Lubricator - P3LL Series
P3LL is a 40mm mini lightweight lubricator that injects an oil aerosol into the flowing air stream, 1/4" ported BSPP/NPT, poly bowl. Max P1 pressure of 10 bar. Temp from 0°C to 50°C.
Global Hi-Flow Mist Lubricator - P3YL Series
P3YL is a 90mm lubricator that injects an oil aerosol into the flowing air stream, 3/4" & 1" ported BSPP/NPT, poly insert & metal bowl. Max P1 pressure of 17.5 bar. Temp from -40°C to 60°C.
P3Z Mist Lubricator - P3ZL Series
P3ZL is a 200mm (inc. flange) large lubricator that injects an oil aerosol into the flowing air stream, 1-1/2" & 2" ported BSPP/NPT, aluminium bowl with manual drain. Max P1 pressure 17.5 bar. Temp from 5°C to 60°C.
Global Mini Mist Lubricator - P31L Series
P31L is a 40mm mini mist lubricator that injects an oil aerosol into the flowing air stream, 1/4" ported BSPP/NPT, poly/metal bowl. Max P1 pressure of 17 bar (Metal). Temp from -10°C to 65.5°C.
Global Compact Mist Lubricator - P32L Series
P32L is a 60mm compact mist lubricator that injects an oil aerosol into the flowing air stream, 1/4",3/8" & 1/2" ported BSPP/NPT, poly/metal bowl. Max P1 pressure of 17 bar (metal). Temp from -10°C to 65.5°C.
Global Standard Mist Lubricator - P33L Series
P33L is a 73mm standard mist lubricator that injects an oil aerosol into the flowing air stream, 1/2" & 3/4" ported BSPP/NPT, poly/metal bowl. Max P1 pressure of 17 bar (metal). Temp from -10°C to 65.5°C.
Stainless Steel Standard Mist Lubricators - PL10 Series
PL10 is a 60mm S/Steel (316) lubricator that injects an oil aerosol into the flowing air stream, 1/2" ported BSPP/NPT, metal bowl fitted with manual drain. Max P1 pressure of 20.7 bar. Temp from -18°C to 82°C.
Global Standard Mist Lubricators - P31L Series (Miniature)
The P31L is a miniature mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Global Standard Mist Lubricators - P32L Series (Compact)
The P32L is a compact mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Global Standard Mist Lubricators - P33L Series (Standard)
The P33L is a compact standard mist lubricator that injects a mist of oil into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
AL (AL200 / AL320 / AL420),a modular style lubricator, provides accurate lubrication of downstream equipment.
Automation Korea Division's AL series is a mist lubricator that injects an oil aerosol into the flowing air stream to automatically provide the correct amount of internal lubrication for air tools and other pneumatic devices.
Two-unit and three-unit close nippled and modular filter regulator and lubricator (FRL) combination units provide attractive, versatile air preparation solutions. Parker offers a range of solutions including various pipe sizes, lightweight corrosion-resistant bodies, durable piston or diaphragm design regulators and fingertip lubricator adjustment.
Pipe Nippled FRL 3-Piece Combo - C628 Series
Parker's C628 is an industrial heavy duty 3-piece pipe nippled particulate filter, regulator and mist style lubricator. The C628 provides accurate pressure regulation, high moisture removal efficiency and delivers oil over a wide range of air flows.
Pipe Nippled FRL 2-Piece Combo - 17G Series
Parker's 17G is a 2-piece pipe nippled integral particulate filter / regulator and micro mist style lubricator. The 17G provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 3-Piece Combo - 17A Series
Parker's 17A is a 3-piece pipe nippled particulate filter, regulator and micro mist style lubricator. The 17A provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 2-Piece Combo - 16G Series
Parker's 16G is a 2-piece pipe nippled integral particulate filter / regulator and micro mist style lubricator. The 16G provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 3-Piece Combo - 16A Series
Parker's 16A is a 3-piece pipe nippled particulate filter, regulator and micro mist style lubricator. The 16A provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 3-Piece Combo - 14A Series
Parker's 14E is a 3-piece pipe nippled miniature particulate filter, regulator and mist style lubricator. The 14E provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 2-Piece Combo - 07G Series
Parker's 07G is a 2-piece pipe nippled integral particulate filter / regulator and mist style lubricator. The 07G provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 3-Piece Combo - 07A Series
Parker's 07A is a 3-piece pipe nippled particulate filter, regulator and mist style lubricator. The 07A provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 2-Piece Combo - 06G Series
Parker's 06G is a 2-piece pipe nippled integral particulate filter / regulator and mist style lubricator. The 06G provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 3-Piece Combo - 06A Series
Parker's 06A is a 3-piece pipe nippled particulate filter, regulator and mist style lubricator. The 06A provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Pipe Nippled FRL 2-Piece Combo - 14G Series
Parker's 14G is a 2-piece pipe nippled mini integral particulate filter / regulator and mist style lubricator. The 14G provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Hi-Flow Modular 2-Unit Mist FRL Combo - P3NCA Series
Parker's P3NCA is a 2-piece modular mounted integral particulate filter / regulator and mist style lubricator. The P3NCA provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Hi-Flow Modular 3-Unit Mist FRL Combo - P3NCB Series
Parker's P3NCB is a 3-piece modular mounted particulate filter, regulator and mist style lubricator. The P3NCB provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Global Hi-Flow Modular FRL Combo - P3YCA Series
Parker's P3YCA is a 2-piece modular mounted integral particulate filter / regulator and mist style lubricator. The P3YCA provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Compact Modular 3-Unit Mist FRL Combo - 06B Series
Parker's 06B is a 3-piece modular mounted particulate filter, regulator and mist style lubricator. The 06B provides accurate pressure regulation, high moisture removal efficiency, and proportional oil delivery over a wide range of air flows.
Global Hi-Flow Modular FRL Combo - P3YCB Series
Parker's P3YCB is a 3-piece modular mounted particulate filter, regulator and mist style lubricator. The P3YCB provides accurate pressure regulation, high moisture removal efficiency and proportional oil delivery over a wide range of air flows.
Compact Modular 2-Unit Mist FRL Combo - 06H Series
Parker's 06H is a 2-piece modular mounted integral particulate filter / regulator and mist style lubricator. The 06H provides accurate pressure regulation, high moisture removal efficiency, and proportional oil delivery over a wide range of air flows.
Standard Modular 3-Unit Mist FRL Combo - 07B Series
Parker's 07B is a 3-piece modular mounted particulate filter, regulator and mist style lubricator. The 07B provides accurate pressure regulation, high moisture removal efficiency, and proportional oil delivery over a wide range of air flows.
Standard Modular 2-Unit Mist FRL Combo - 07H Series
Parker's 07H is a 2-piece modular mounted integral particulate filter / regulator and mist style lubricator. The 07H provides accurate pressure regulation, high moisture removal efficiency, and proportional oil delivery over a wide range of air flows.
Compact Modular 3-Unit Micro-Mist FRL Combo - 16B Series
Parker's 16B is a 3-piece modular mounted particulate filter, regulator and micro mist style lubricator. The 16B provides accurate pressure regulation, high moisture removal efficiency, and proportional oil delivery over a wide range of air flows.
READING TECHNOLOGIES
Eliminex® High Flow Separators
Eliminex Mainline Separator:
Eliminex Mainline Separator Combo:
Eliminizer® Point-of-Use Dryers/Filters
Eliminizer Mainline Separator:
Eliminizer Combo Mainline Separator Combo:
Coalescing Oil Removal Filters
Coalescers:
Oil Extractors with Activated Carbon
Oil Extractor:
Oil Extractor Combo:
Pressure Regulators
Regulators & Heavy Duty Regulators: Different sizes and styles to meet your needs.